Loading the content... Loading depends on your connection speed!

airsoft law rules regulation

“18 U.S.C. 921(a)(3): DEFINITIONS (FIREARM)
26 U.S.C. 5845(a)(7): DEFINITIONS (FIREARM)
26 U.S.C. 5845(i): DEFINITIONS (MAKE)
Certain integral devices intended to diminish the report of paintball guns are not “firearm silencers” or “firearm mufflers” under the Gun Control Act of 1968 or the National Firearms Act.
ATF Rul. 2005-4

The Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) has received requests from manufacturers of paintball guns for evaluation and classification of integral devices intended to diminish the report of a paintball gun. Specifically, the manufacturers have asked whether the device would be considered a “silencer” as defined in the Gun Control Act of 1968 (GCA), 18 U.S.C. Chapter 44, and the National Firearms Act (NFA), 26 U.S.C. Chapter 53.

The sample submitted is a paintball gun with a ported device attached to the barrel. The paintball gun uses compressed air to expel a projectile. The paintball gun has a barrel with a smooth bore 12 1/4 inches long and 1 inch in diameter. The barrel is permanently welded to the paintball gun. The section of the barrel that the device is attached to has an internal diameter of .68 inches and is ported with 20 openings. Ten of the openings are rectangular in shape and are approximately .430 inches wide and 1 inch in length. The other 10 openings areoval in shape and approximately .25 inches wide and 1 inch in length. Two end caps, each with a diameter of 1.5 inches, are permanently welded to the barrel at either end of the ported section of the barrel. A section of plastic tube approximately 8 inches in length and 2 inches in diameter covers the ported section of the barrel. It is attached by sliding over the paintball gun barrel and is held in place by two rubber “O” rings that are affixed to metal bushings. These metal bushings are permanently welded to the barrel, one toward the rear and oneat the muzzle end of the barrel. The plastic tube, however, can be removed.

To determine whether the ported barrel and outer sleeve would function as a silencer, it was removed by cutting with a hack saw. A threaded adaptor with tape wrapped around it was utilized so the device could be attached to a .22 caliberRuger Mark II pistol. With the device attached, a sound meter test was performed, with five shots being fired with the device attached and five shots fired without the device attached.

The testing indicated that the attachment of the device resulted in a 7.98-decibel sound reduction.

The GCA defines the term “firearm” as:(A) any weapon (including a starter gun) which will or is designed to or may readilybe converted to expel a projectile by the action of an explosive; (B) the frame orreceiver of any such weapon; (C) any firearm muffler or firearm silencer; or (D) anydestructive device. Such term does not include an antique firearm.18 U.S.C. 921(a)(3)(C).The definition of “firearm silencer” and “firearm muffler” in 18 U.S.C. 921(a)(24)provides as follows:The terms “firearm silencer” and “firearm muffler” mean any device for silencing,muffling, or diminishing the report of a portable firearm, including any combinationof parts, designed or redesigned, and intended for use in assembling or fabricatinga firearm silencer or firearm muffler, and any part intended only for use in suchassembly or fabrication.The NFA defines the term “firearm” to include any silencer as defined in section921 of the GCA. 26 U.S.C. 5845(a)(7).The term “make” is defined in the NFA to include manufacturing, putting together,altering, any combination of these, or otherwise producing a firearm. 26 U.S.C.5845(i).

The paintball gun examined by ATF is not a “firearm” as defined, because it doesnot, is not designed to, and may not be readily converted to expel a projectile bythe action of an explosive and does not utilize the frame or receiver of a firearm.The sole issue presented is whether the ported barrel and outer sleeve are afirearm muffler or firearm silencer as defined in the GCA and NFA.The design characteristics of the ported barrel and outer sleeve are similar tothose of conventional commercial silencers. The barrel is ported to allow theescape of gases from a fired round and the outer sleeve dampens or muffles thesound when a round is fired. Moreover, the sound meter test indicates a reductionof 7.98 decibels when the ported barrel and sleeve were attached to a .22 caliberpistol, which is consistent with the sound reduction resulting from the use ofcommercial silencers.Noteworthy, the definition of “firearm silencer” and “firearm muffler” requires thatthe device be one for diminishing the report of a portable firearm.

The deviceunder consideration is permanently attached to and an integral part of a paintballgun, which is not a firearm as defined in the GCA or NFA. The device cannot beremoved from the paintball gun without destroying the barrel and rendering thepaintball gun unusable. Under these circumstances, the integral device is not afirearm muffler or firearm silencer.However, once the device is cut from the paintball gun, it can be used to diminishthe report of a firearm. As stated previously, the design characteristics of thedevice are consistent with those of commercial silencers, and testing indicates thatthe device functions to reduce the report of the firearm. Moreover, removal of thedevice from the paintball gun indicates some intention to utilize the device forsomething other than reducing the report of the paintball gun. Because the devicewill no longer be permanently attached to an unregulated item, and because of itssilencer design characteristics, removal will result in the making of a silencer underthe NFA and GCA.

This is consistent with the definition of “make” in the NFA, asremoval of the device results in production of a silencer.Making of a silencer by an unlicensed person for personal use does not requireany license or notification to ATF under the GCA. However, under the NFA themaking of a silencer must be approved in advance by ATF. Unlicensed personsmust file an ATF Form 1, Application to Make a Firearm, pay a $200 making tax,and comply with all other provisions of the law prior to making the firearm.Approval of the Form 1 results in registration of the silencer to the maker.Subsequent transfers of the registered silencer must be approved in advance byATF. Possession of a silencer not registered to the possessor, and a making ortransfer that does not comply with the NFA and regulations are punishable byimprisonment for up to 10 years, a fine of $250,000, or both.Held, a device for an unregulated paintball gun, having a permanentlyaffixed, integral ported barrel and other components, that functions to reduce thereport of the paintball gun is not a “firearm silencer” or “firearm muffler” as defined,as the device is not one for diminishing the report of a portable firearm.Held further, removal of the permanently affixed ported barrel and othercomponents from a paintball gun is a “making” of a silencer under the GCA andNFA that requires advance approval from ATF.

Date approved: October 12, 2005
Signed by:
Carl J. Truscott

This letter comes from the ATF’s official website and can be found at this link: http://www.atf.gov/regulations-rulings/rulings/atf-rulings/atf-ruling-2005-4.pdf

Please note that www.77airsoft.com is not responsible or do not hold any legal liability for the above content.


Free T-shirt
 plastic gun
Contact Us